Calculadora del diámetro máximo de la bola

Calculation Result

Dureza de la roca (escala de Mohs f) Tipo de molino Coeficiente de recomendación K Explicación lógica
f<10 (blando) Todos los tipos 18-22 Los minerales blandos son frágiles y no requieren bolas de molienda excesivamente grandes; las bolas forjadas pueden ser ligeramente subdimensionadas para aumentar el número de puntos de molienda.
10 ≤ f ≤ 15 (medio-duro) Una molienda gruesa/SAG 24-28 Condiciones de operación estándar, coeficiente clásico. Esto refleja la tenacidad de las bolas forjadas y permite seleccionar un valor intermedio a superior dentro del rango especificado para garantizar una resistencia adecuada al impacto.
10 ≤ f ≤ 15 (medio-duro) Segunda etapa/Rectificado 20-24 Cuanto más fina sea la alimentación de rectificado, menor será el requisito de impacto; por lo tanto, debe seleccionarse un valor más bajo.
f>15 (difícil a muy difícil) Todos los tipos 28-32 Los minerales duros requieren una mayor energía cinética. Para la forja de bolas resistentes al impacto, es aconsejable utilizar valores cercanos al límite superior para garantizar una trituración eficaz.

Calculadora de la relación de diámetro de la bola

mm
Model name Applicable scenarios
First-stage grinding,F80>10mm
F80≈5-10mm
Second-stage Grinding,F80<5mm

Calculation Result

Proceso de selección de materiales

Image Name

Calculadora de tasa de llenado y estimación del consumo por unidad

Mill Type Process Stage / Characteristics Recommended Filling Rate Range Your Adjustment Suggestions (Notes in Configurator)
Semi-Autogenous Mill (SAG) Normal Operation 8% - 15% (Steel Ball Filling Rate) Use high-toughness forged balls; allows stable operation at the upper limit of ball charge, reducing impact damage to liners from broken balls.
Total Filling Rate (incl. Ore) 25% - 32% High-toughness forged balls allow operation at the upper limit of total filling rate, increasing throughput while maintaining safety.
Overflow Ball Mill Primary Coarse Grinding 38% - 42% Forged balls have good fluidity and high actual effective filling rate; suggest starting optimization from 40%.
Secondary / Re-grinding 35% - 40% Forged ball gradation dominated by small balls achieves higher grinding efficiency at slightly lower filling rates.
Grate Discharge Ball Mill Primary Coarse Grinding 40% - 45% Forged balls paired with grate plates are a golden combination for production increase. Allows safe adoption of higher filling rates, utilizing the forced discharge advantage of grate plates.
Secondary Grinding 38% - 42% Uniform wear of forged balls reduces the risk of clogging the grate plates.
Multi-compartment Tube Mill 1st Compartment (Coarse Grinding) 28% - 32% Forged balls dominated by large balls have strong impact force in the 1st compartment; filling rate can be slightly lower than in ball mills.
2nd Compartment (Fine Grinding) 25% - 28% Forged balls maintain shape well, maintaining high grinding efficiency even at lower filling rates.
3rd Compartment (Ultra-fine) 22% - 25% Consider replacing small balls with cylpebs; forged cylpebs offer superior wear resistance.
Dry Ball Mill All Types 28% - 35% Material fluidity is poor in dry grinding; filling rate needs to be lower than wet grinding. Forged balls have good self-cleaning properties and do not easily stick to material.
Wet Ball Mill All Types 35% - 45% Wet grinding can operate at higher filling rates. Forged balls have smooth surfaces, resulting in better slurry fluidity.
Rod Mill Wet Process 40% - 50% (Steel Rods) Rod mills rely mainly on line contact; filling rate can be higher than ball mills.
Dry Process Around 35% (Steel Rods) Filling rate needs to be reduced for dry process rod mills.
Open Circuit Mill (Single Compartment) Full Stage 25% - 30% Open circuit mills need to control material flow rate; filling rate should not be too high.
Closed Circuit Mill (Closed Loop) Full Stage 30% - 40% Closed circuit mills can be adjusted via classifiers; filling rate can be appropriately increased.
Ore Type Coefficient (H) Typical Ore Examples
0.04-0.06 Limestone, Phosphate Ore, Partial Bauxite
0.07-0.10 Most Copper Ores, Gold Ores, Porphyry Ores
0.11-0.15 Magnetite, Hard Lead-zinc Ore, Some Granites
0.16-0.22 Quartzite, Taconite, Extremely Hard Gold Ore
Product P80 (Mesh/mm) Process Stage Coefficient (F) Description
Coarse Grinding / Primary Grinding 1.0-1.2 Mainly impact crushing with relatively low energy consumption.
Standard Fineness / Secondary Grinding 1.3-1.5 Industry standard fineness with enhanced grinding effect.
Fine Grinding / Re-grinding 1.6-1.9 Mainly grinding and attrition, with a sharp increase in energy consumption.
Ultra-fine Grinding 2.0-3.0+ Special field with very high medium unit consumption.
Steel Ball Type (Forged) Typical Hardness (HRC) Correction Coefficient (M) Value Proposition & Application Scenarios
55-58 1.0 (Benchmark) Economical choice for medium-hard ores with low impact.
58-60 0.85-0.95 Cost-effective choice, unit consumption significantly lower than the benchmark by improving hardness.
58-62 0.75-0.85 Mainstream high-performance product. Excellent hardness-toughness combination for most high-impact and high-wear conditions.
60-63+ 0.65-0.75 High-end solution for extremely hard ores and SAG mills, pursuing the longest service life and lowest comprehensive cost.
55-60 0.8-1.1 Special working conditions. In acidic pulp, wear resistance may yield to corrosion resistance, and the coefficient needs specific evaluation.

Calculation Result